Installing hockey stick holders

Installation of Breakaway Displays™ brand hockey stick holders is simple and takes just a few minutes. Each of our products come with everything you will need to mount, in standard wall applications, no additional hardware required.

With each of our products we provide mounting instructions.
Below are instructions along with pictures and additional notes for:

  1. Original Hockey Stick Holder
  2. Goalie Spacers™
  3. Cross Mount Spacers™

 

Original Hockey Stick Holder

Package Contents:

  • 2 Brackets (wood piece is for display only and can be discarded)
  • Instruction Card
  • Mounting Template
  • 2 Screws and 2 Anchors

Mounting Instructions and Tips:

If you're hanging a game-used goalie stick, you may need Goalie Spacers. Read here for more information.
  • Lay template along stick shaft (#1 cross-hair on top handle side), slide template up and down handle to desired position.
    It's a good idea to center the mounting brackets as much as possible on the stick shaft
    Center template as much as possible on hockey stick shaft
  • Be sure brackets will not be obstructed by things like tape on stick, etc.
    Take some time and plan where the brackets will be holding on to the stick
    Avoid bracket obstructions on the stick
  • Be sure brackets will not obstruct autographs, etc.
  • It’s ideal to use #2 cross-hair, but if necessary, use another mark provided.
  • Be sure brackets fit on stick shaft at cross-hairs #1 & #2 (or desired mark).
    Test fit brackets on stick at selected mounting points
    be sure brackets fit, and do not obstruct anything, at mounting points
  • Brackets do not need to be overly tight to hold stick securely.
    Brackets should fit snug, but do not need to be tight to hold the stick at any angle
    hangers should hold stick firmly, but easily slide on and off
  • Find the location (on wall, ceiling, etc.) to hang your hockey stick.
    Hold the hockey stick up to the wall. Check out different angles. Try different looks before drilling holes.
    use our hockey stick hangers to mount horizontally on the wall displaying your hockey stick at any angle is possible vertical? - no problem with Breakaway Displays™ brand hockey stick holders
  • Position template on wall, allowing space off ends of template for the handle and blade.
    Be sure there is adequate space off each bracket for the extra portion of the stick
    be sure there is enough room for the extra stick lengths beyond each bracket
  • Mark on wall at #1 cross-hair and #2 cross-hair (or desired mark).
    You can use a pencil or pen, and just push through the template at the appropriate cross-hair, leaving marks on the wall
    mark at the #1 and #2 template cross-hairs
  • Drill 3/16 inch holes for anchors on both marks, insert anchors.
    You do not need the anchors if you are mounting into studs. The provided screws will work in stud-mount applications.
    drill 3/16 inch holes, and insert anchors
  • On bracket, lift up felt flap, insert screw through felt side first.
    insert screw through felt side first
  • Place bracket over anchor (metal side of bracket towards wall) and screw into anchor.
    insert screw through felt side first, metal side of bracket towards wall, screw in snugly
  • Cover screw head with felt flap.
    This little felt flap protects your hockey stick by covering all hard, metal surfaces
    cover the screw head with the felt flap, this will further protect
  • Gently twist brackets if needed to align with stick.
    That's it! You're done! Sit back, admire it. Tell your friends, send us pictures. Thanks for using Breakaway Displays™!
    cover the screw head with the felt flap, this will further protect
  • Show off your sticks, Send us your pictures!

 

Goalie Spacers™

Goalie Spacers™ should not be purchased alone. You will also need a set of Original Hockey Stick Holders in order to display a game-used hockey goalie stick.

Package Contents:

  • 2 Goalie Spacers
  • 2 Screws (longer than the screws provided with the Original Hockey Stick Holder)
  • Instruction Card

Mounting Instructions and Tips:

  • Discard the screws provided with the Original Hockey Stick Holder and use the longer screws included with this Goalie Spacer.
  • Mount the stick as indicated from the directions enclosed in the Original Hockey Stick Holder packaging.
  • Place these Goalie Spacers between the wall (mounting surface) and each of the brackets to provide the needed space for the taped knob.
    use the longer screws provided insert screw through bracket, felt side first, then through spacer finished - spacer hides behind hockey stick holder bracket
  • Show off your sticks, Send us your pictures!

 

Cross Mount Spacers™

Cross Mount Spacers™ should not be purchased alone. You will also need 2 sets of Original Hockey Stick Holders in order to hang 2 hockey sticks in a cross formation.

Package Contents:

  • 2 Cross Mount Spacers
  • 2 Screws (longer than the screws provided with the Original Hockey Stick Holder)
  • Instruction Card

Mounting Instructions and Tips:

  • To hang 2 sticks in a cross formation, you will need to determine the desired angles of the hockey sticks.
  • You can tape the two mounting templates together to assist in determining the desired angle (mounting templates are included inside the Original Hockey Stick Holder packaging).
  • Generally, a right handed and a left handed stick are required to hang in the cross formation.
  • Mount the first stick as directed (directions for hanging a hockey stick are included inside the Original Hockey Stick Holder packaging).
  • For the second stick, discard the screws provided with the Original Hockey Stick Holder and use the longer screws included with this Cross Mount Spacer.
  • Place these Cross Mount Spacers between the wall (mounting surface) and each of the brackets to lift the second stick over the first.
  • Show off your sticks, Send us your pictures!